Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab on Swingmaster Swingmaster - Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab
Call Toll-Free: (800) 457-1224 - E-mail: Sales@SwingmasterCorp.com

Gadgets powered by Google
  



Swingmaster Twitter

 

 

 
Search Catalog
      GO   
 All Categories    Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab
All Categories > Model 361 Swing Cab Swingloader- 20,000 Pound Capacity > Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab > Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab  
Request Information

Model 181TC Swingloader- 10,000 Pound Lift Capacity with Tilt Cab



Model 181TC

larger image

181TC Drawing

larger image



Specifications · Powertrain · Torque Converter · Transmission · Wheels and Tires · Steering System · Service Brake System · Parking Brake System · Electrical System · Engine Air Intake System · Fuel System · Hydraulic System · Control Valves · Cylinders · Swing Drives Systems · Machines General Dimensions · Max. Travel Speeds (MPH on Rubber Tires) · Note

Specifications

Lifting Capacity

10000 Pound

Carrying Capacity

10000 Pound

Mainframe

Welded construction of structural steel shapes and plates.

Construction

Steel

Heavy Duty Railroad Axles

Heavy Duty Ribbed, Two drive steer axles with planetary type gear reduction at wheel ends.

Drive System Controls

Air foot throttle and hand operated electric controls for direction, gear, range, and axle disconnect.

Suspension System

Rear Axle Oscillates nine degrees on each side of center. Mechanical travel stops to limit oscillation for over the side lifting and High Rail use.

Engine Exhaust System

Low Restriction, Muffler and Tail Pipe Extension

Engine Cooling System

Downflow Radiator and Blower Fan

Compressed Air System

12 CFM to 24 CFM Compressor Direct Driven from Engine Power Take Off

Operator Cab

Partial Width Crew Cab 2 Men. Fully Enclosed Tiltable ROPS Cab with Adjustable Operator Seat, Heater, Defroster, Windshield Wipers, Two Doors with Sliding Windows, Interior Light, and Outside Rear View Mirrors.

Boom Turntable

Large Diameter Ball Bearing with Turntable Swing Lock

Boom Construction

One piece welded design of steel plate and shapes

Standard Equipment

4-Wheel Air Over Hydraulic Brakes
4-Wheel Drive with Rear Axle Disconnect
4-Wheel Power Steering
12 Volt Battery with Disconnect
14-24 Tires on Single Dish Wheels
Adjustable Seat
Air Horn
Alternator
Back-up Alarm
Blower Fan
Defroster
Diesel Engine
Dome Light
Dry Type Air Cleaner
Electric Starting
Engine Compartment Side Panels
Headlights
Heater
Hydraulic Oil Level Sight Gage
Locks on All Tanks and Tool Box
Muffler
Planetary Axles
Power Shift Transmission
Quick Disconnect Hydraulic System Diagnostic Check Points
Rear View Mirror
Removable Hydraulic Tank one Function Attachment Hydraulics
Tail and Stop Lights
Torque Converter
Turntable Lock
Wipers

Powertrain

Engine Make

Cummins

Max. Horsepower

140 @ 2300 rpm

Peak Torque (Foot-Pounds)

410 @ 1400 rpm

Governed RPM

2300 rpm

Torque Converter

Stall Multiplication Ratio

2.29:1.00

Drive

Offset

Drive Ratio

0.965:1.00

Pump Drive Ratio

0.951:1.00

Oil Filler

Remote mounted

Transmission

Type

“Six Speed” Power Shift

Number of Drive Gear Ratios

3

Number of Gear Ranges

2

Axle Disconnect

Rear Axle

Clutch Cutout

Standard

Wheels and Tires

Tires

14.00 x 24

Standard Wheels

Single dish, 10 W Rim inside to inside of tires 65 inches (Loaded Section)

Optional Wheels

Dual dish, 8 TG or 10 W Rim inside to inside of tires 75 inches (loaded section)

Steering System

Type

Rigid Frame with Steerable Axles

Control

Full power Hydraulic

Selectable Modes

4 Wheels, Crab, Front Only and Rear Only

Turning Radius (Curb Clearance)

20 feet 6 inches

Cylinders

Double acting, 3” bore, 6.5” stroke, chrome plated piston rods.

Service Brake System

Type

Outboard Style Single Caliper Disc Brakes

Disc Diameter

19 in

Location

Axle Wheel Ends

Actuation

Dual Circuit System Air over Hydraulic

Control

Foot control in Cab

Parking Brake System

Type

Mechanical Drum

Diameter

10 in

Width

2 in

Location

Transmission Output Yoke

Actuation

Cable

Control

Over center lever in cab

Electrical System

Voltage

12 V

Alternator Output

130 A

Standard Gauges

Air Pressure
Clutch Pressure
Engine Oil Pressure
Engine Water Temperature
Fuel Tank Level
Hourmeter
Torque Converter Oil Temperature
Transmission
Voltmeter

Warning Lights

Low Engine Oil Pressure, High Engine Water Temperature, Low Air Pressure, Alternator Not Charging

Battery

760 Cold Cranking Amps with Disconnect Switch.

Engine Air Intake System

Type

Dry, Two Stage (Centrifugal Precleaner, Paper Main Element)

Restriction Indicator

Standard, Mounted alongside air cleaner

Fuel System

Tank Capacity

52 gal

Filters

Spin on Primary Strainer and Spin on Secondary Filter

Hydraulic System

Reservoir

75 Gallon Removable Hydraulic Tank with Removable Cleanout Cover and Pad Lockable Filler/breather Capacity

Suction Strainers

100 Mesh Strainers Mounted in the Hydraulic Tank on Each Pump Suction Line

Primary Pump

Double section gear type, direct driven from accessory drive on torque converter. Supplies oil flow for Boom, Attachment, and Hi-rail functions.

Secondary Pump

Double section vane type, direct driven from accessory drive on torque converter. Supplies oil flow for Steering and Remote controls.

Control Valves

Primary

Two spool, hydraulic pilot operated with manual override

Secondary

Five spool, hydraulic pilot with manual override

Controls

Low Effort Hydraulic Remote Controls for Boom Lift, Boom Swing, Attachment Tilt, and Auxiliary Attachment Function, with Manual Override on Control Valves.

Cylinders

Boom Lift

2 Double acting 6” bore x 24.5” stroke with Hydraulic Holding Valves

Attachment Tilt

1 Double acting 6” bore x 34” stroke with Hydraulic Holding Valves

Filters

Return Line Cartridge Type, 10 micron nominally rated element with Magnetic Element

Swivel

9 Port Hydraulic

Swing Drives Systems

Type Drive

Cylinder, Chain and Sprocket

Rotation

180 degrees (90 degrees each side of center)

Speed

Equivalent to 3.5 rpm

Machines General Dimensions

Weight

28000 lbs. (Base machine without Hi-rail)

Chassis Length

204.75 in

Chassis Width

96 in

Chassis Width Over Tires

97.25 in

Height

118.75 in

Max. Travel Speeds (MPH on Rubber Tires)
Forward and Reverse Low Range High Range
1st 2nd 3rd 1st 2nd 3rd
2.3 4.0 12.0 4.6 9.0 26.0




Note
Additional attachments and information available on request. Materials and specifications are subject to change without notice. Some equipment described is optional and available at additional cost.


    border="0" Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

 MORE IMAGES 

· Model 181TC Hi Rail and Tilt Cab

· Model 181 TC with 20 Foot Hydraulic Boom and Magnet

· Model 181 TC with 30,000 Pound Winch

· Model 181 TC with Brush Cutter

· Swingmaster Quick Coupler Attachment

· Model 181 TC with Fork Tie Baler

· 96” Wide Track Cleaning Bucket

· 1 1/4 Yard Bucket and 4 Yard Snow Bucket

· Model 181 TC with Backhoe

· Tilt Cab Pumps, Drive Shafts, and Hydraulic Cylinders

· Tie Exchanger

· Manual Hydraulic Controls Compartment

· Model 181 TC with 360 Degree Tie Grappler

· AAR Adjustable Coupler with Train Air Brakes

· 20 Foot Telescopic Boom

 DOWNLOADS 

width= Tie Exchanger Video

Request Information
Site created by ThomasNet Web Solutions
Swingmaster